These dishes and racks are made of resistant and strong POM. The rack takes 24 slides in an upright position and it is 85x32x63mm high. At the handling tab overall height is 90mm. The slots are 2mm wide.
The dish's internal dimensions are 95x40mm with a slight taper towards the bottom. Overall height is 96mm and the dish has a rim around the top making the outer dimensions 104x48mm.
The set comes with 12 slide staining dish (10 grey, 2 green), 2 slide staining racks, and a powder-coated metal housing.
This combination dish and rack are excellent substitutes for the lofty-priced name-brand alternative.
12 PP dishes
The Manual Slide Staining Set can be used for histological or cytological staining procedures. The set provides simultaneous use of up to 12 solution wells, each deep enough to permit total immersion of 2.5 to 7.6 cm slides.
The tamped metal frame is solvent-resistant, with a snap-locking cover that prevents spills. Ten white polypropylene dishes and two green solvent-resistant dishes are included.
Tight-fitting lids for each solution dish help eliminate evaporation. Comes complete with 12 dishes and lids, a 12-unit metal carrier and a drain tray cover.
Accessories for the Tissue-Tek® Manual Slide Staining Set include green and white staining dishes and a 24-Slide Holder with detachable handle.
In Australia Tissue Tek items are overpriced. The staining set is also prone to transit damage. We don't offer this item to overseas destinations.
A universal slide rack and container for Autoradiography and all staining techniques. Moulded of black polyoxymethylene-poly-acetal plastic which has great advantages over glass in all cytological and histological laboratories. The rack and dish are easy to clean and resistant to chemicals used in staining procedures.
The slide rack has an open bottom for rapid draining. It holds 26 x 76mm slides in slots numbered 1 to 25. The handle folds flat on either side. Maximum use temperature of POM is 130°C.
External dimensions without rack handle extended: 92mm (L) x 80m (W) x 32mm (H)
Height has been measured from the base to the top of the side - where the handle is joined to the sides. The handle adds extra height (~30mm extra), however when not in use the handle sits flush with the height of the side.
The 94 x 81 x 49mm high staining dish has a light-tight cover with a compartment for a drying agent, and a perforated slide partition to support the drying agent. The partition has index numbers and a surface for writing. A removable clip is placed on the top edge of the dish, permitting stain solution to drain back into the reservoir from the tilted rack. The small size dish saves on staining liquids, developing fluids and intermediates, as only 150mL is needed. Actual capacity is 250mL. The light-tight lid is essential for easily evaporated baths.The dish is easy to clean and especially suited to storing enzymes. The cover will not jam in freezer storage.
Kit consists of dish and rack.
Dish glass, rack SS
Fine example of the best from China. Very well made glass dish with lid. Internal dimensions are: 65 x 75 x (deep) 80mm. The dishes are tapered and so lengths and widths are greater at the top. The lid may be used with the SS rack in place.
The SS rack holds 30 slides upright. Dimensions are 76.3 x 70.6 x (high)78mm; slots for slides are 2mm wide. The design uses less staining solution and does not stain the slides' labels.
Excellent quality, European made, all glass staining dish, lid and rack, moulded soda glass. Metal handle. Holds 10 slides or 20 back to back.
Dimension of dish
Inner: L93 x W73 x H60mm
Outer: L104 x W84 x H68mm
Staining dishes made from moulded glass with a fitted glass lid.
Outside dimensions: 105 x 86 x 75mm
FOR STAINING DISH
A stainless steel slotted rack, for up to 50 slides. A variety of slide sizes are accommodated: 76 x 25mm, 76 x 38mm and 76 x 51mm. The rack is made from non-tarnishable stainless steel and is resistant to most processing and staining solutions. The handle is moveable to allow closure of the dish and insertion and removal of the slides.
A well made staining dish with lid. Inner dimensions near the base are: 75 x 145mm; depths is 86mm. Inner dimensions near the top are 82 x 153mm. The dish takes 2 of the H4284-R30 racks or one of H4285-R60. The H4285-R60 sits about 5mm off the bottom, the staining dish lid will fit the dish with this rack inside.
This SS rack holds 60 slides upright. Slots for slides are 2.1mm wide.
The design uses less staining solution and does not stain the slides' labels.
This rack suits dish H4283‐60 ‐ it sits about 5mm off the bottom, the staining dish lid will fit the dish with this rack inside.
|Cat. No.||Length (mm)||Width (mm)||Height (mm)|
An unbreakable, tapered square jar with a domed, shallow-thread screw cap. Internal grooves hold up to 10 standard 25 x 75mm slides back to back. 59mm dia. base, 114mm high.
See also Slide Mailer H44200, which is similar to the Coplin jar.
For 8 slides, or 16 back to back. Supplied complete with lid. Moulded soda glass.
Grooved sides holding 10 slides, or 20 back to back. Supplied complete with lid. Moulded soda glass.
Inner: L78 x W58 x H35mm
Outer: L90 x W70 x H44mm
Dish PMP, rack PP
- Made from PMP/PP; wet autoclavable.
- Maximum use temperature is 135ºC
- Accommodates up to 20 slides (76 x 26mm)
- Removable snap-on handle. Including handle it measures 70 x 86 x 21mm.
SLIDE STAINING DISH PMP
The dish is made from polymethylpentene "glass clear" for use with the above polypropylene staining rack. PMP's maximum use temperature is 175ºC. Two lids are included; the second lid may be used with the staining rack.
70 x 86 x 21
81 x 101 x 86.5
The EasyDip™ slide staining system has two components, a square staining jar and a 12‐position vertical slide staining rack. Jars can be loosely joined to each other laterally, ensuring they are kept in the same order when moved around on the lab counter. They are available in five different colours to help identify contents or applications.
The EasyDip™ staining jar, being made from acetal plastic, will not break like most glass jars do. It resists attacks from most staining reagents including alcohol and xylenes but not phenols. The wide base offers greater stability while the inside is recessed, allowing for a smaller reagent volume of only 80mL. Ideal for frozen sections, small jobs and special processes.
Dimensions: 64mm x 76mm x 92mm
The EasyDip™ slide staining rack holds up to 12 slides of 25 x 75mm or 26 x 76mm with a thickness of 1.0 to 1.2mm. These racks are safe at temperatures up to 120°C. The lid completely covers the EasyDip™ slide staining jar to minimise spills and evaporation. The handle is permanently attached to the rack for easy insertion or removal of the slide. The base of the rack is placed in the vertical position to ensure the slides are in place, and are rotated sideways for easy slide removal.
Dimensions: 60 x 64 x H97mm
The EasyDip™ stainless steel holder is designed to hold six EasyDip™ staining jars together. For your convenience, we offer EasyDip™ Slide Staining Kit. Kit consists of one Staining Jar and one Staining Rack, colour white.
Dimensions: 425 x 102 x 38mm (L x W x H)
The EasyDip™ slide staining kit consists of one white staining jar and one staining rack.
An ingenious rack that fits across the laboratory sink and may be used to support slides or dishes during staining procedures. Clean-up could not be simpler.
Two 6.3mm diameter stainless steel rods, held 50mm apart by a brass end-block and a sliding block (both chrome plated) form the work base. The sliding movement and an anti-wobble/height adjustment is set by thumbscrews. Total length is 520mm.
- The Five Slide Gripper accommodates five microscope slides for staining procedures.
- It fits most Coplin and round open staining jars.
- It is made from materials resistant to all chemicals andsolvents used in staining.
- It withstands drying temperatures up to 80ºC.
Slide Holder may be used to:
- Fix frozen sections in acetone.
- De-paraffinise and re-hydrate paraffin sections.
- Isolate sections on the slide with a PAP Pen (ID310)
- Immunostain, incubate and wash.
- Counter stain.
- Mount coverslips.
The holder, excluding the handle measures 157 x 90mm.
Made from polished stainless steel.
H436 holds five coverslips (or ten back to back) 24mm wide, any length.
With 127mm handle for use in Coplin jars.
H439 holds 25 coverslips 22mm wide. The case is 28mm wide and length 85mm.
Holds 10 coverslips. Fast and easy cleaning, surface-treating and drying. Can accommodate all coverglass sizes including 18, 22 and 25mm.
Durable and hassle free one piece polypropylene rack, does not require assembly and is chemically and thermally resistant. Autoclavable.
Innovative design includes a notch to secure coverslips with a rubber band or loop of monofilament.
Fits inside a 100mL beaker with space underneath for a small stirring bar.
For TEM grids
These silicone rubber pads have a series of cut slots. When the pad is curved along the slots' axis, they open up and grids may be inserted. Pads hold grids vertically and single drops of staining solution can be applied to one or both sides of the grids. Washing by "flooding" or "irrigation" is safe and time effective. Vertical grid position reduces contamination. PSTlogo indicates top of pad and direction of slots.
Designed to handle up to 25 grids at one time or as few as a single one.
- Greatly reduces the chance of mechanical damage
- Ensures equal staining and rinse times
- Simple alpha-numeric system for easy identification of each grid.
The plastics used are not acid resistant and the staining vessels are designed for aqueous solutions or stains dissolved in either ethanol or methanol. The Grid Staining Matrix System consists of four components: the staining matrix body with handle; matrix cover and two staining vessels.
Volume of stain required:
21 - 25 grids 11mL
16 - 20 grids 9mL
11 - 15 grids 7mL
06 - 10 grids 5mL
01 - 05 grids 3mL
How to use:
A. Remove the cover from the body and load the number of grids to be stained in the wells in the body. Start with the bottom row first and fill completely before moving to the next row.
B. Slide the cover over the body until the handle on the cover engages with the retaining pin on the handle of the body. You may need to gently lift the cover handle with a fingernail so that it will slide over the retaining pin and lock.
C. Place the matrix into an empty staining vessel. Add the appropriate volume of stain for the number of grids being processed by allowing the stain to flow down the inside of the vessel, using a pipette or similar tool. To remove trapped air in a grid containing well, move the matrix forward and then backward in the staining vessel. This will pull the trapped bubbles out of the wells. Be careful not to spill reagents during this process.
D. Rinsing grids in the matrix can be done in beakers or by using the staining vessel after it has been cleaned.
Stain, rinse and dry slides on a single working tray.
Made of polypropylene and polyethylene blend. This rugged staining tray provides a clean, fresh working surface for up to eight slides. Base has a deep well which holds 38ml of liquid. Top grip on lid, recessed handles on base along with two pour spouts on base, facilitate transport and waste removal. The dark color of the base and lid make it ideal for light sensitive luminescent and UV applications. Set includes 4 bases and 1 lid.
- Economical alternative to metal trays
- Single use avoids cross-contamination
- Sturdy, yet light weight and compact
- 305mm x 127mm x 29.5mm (12" x 5" x 1-5/32")
An ideal device for immunohistochemistry slide staining/ treatments and whenever specimens are stained for lengthy periods without drying and with only drops of solution. The StainTray™ has a black base made from tough ABS plastic, withstanding a wide range of chemicals (except chlorinated hydrocarbons). It will accept up to 20 slides on four plastic rails covered with a polymer strip, which grips the slides even if the tray is held at an angle. When humidity is needed, the wells between the rails will hold the water securely without splashing. Rails are raised not only to avoid water touching the slides but also make the slides more easily retrievable. The base will also catch excess stain solution that drips from the slides. Four rubber feet make the base more stable. Units are stackable to save space.
This tray is not only suitable for routine staining requiring a humid chamber but is also ideal for haematology, cytology and microscopy laboratories.
Two covers are available:
A clear cover, allowing for visual examination. Made from PETG with a temperature range of ‐20°C to 60°C.
A black cover for fluorescent work. Made from ABS with a temperature range of ‐80°C to 80°C.
Dimensions with the cover
20‐Slide unit: 380 x 240 x 45mm.
Also available: 10‐slide unit
Separate lids ‐ ask
This is a low‐cost, high precision moisture chamber for ten slides. Every moisture chamber is divided into ten individual compartments with approximately 12.7mm empty space between the compartments. When the chamber lid is closed, eight barrier dividers are placed into the empty spaces between the microscope slide compartments completely isolating all compartments. This is a very desirable feature when doing immunostaining.
The microscope slides are placed on four pedestal posts and four corner posts each 11.5mm high, thus raising the surface of the slides approximately 12.7mm off the floor to keep the slides away from the water below and making the slides easily retrievable (either by hand or by forcep).
The chamber is fabricated out of heavy‐duty polystyrene with an air‐tight design to keep moisture in. The chamber is designed to be stackable in order to save counter and/or refrigerator space.
Available in clear, black and amber.
This staining dish is made from clear glass and has 10 cells in 2 rows of 5 each. Each cell is 2mm deep and holds 0.15mL of solution. Very useful in specimen preparation, EM staining, and Boerner-Jones-Lukens microflocculation test.
Measurements: 108 x 57mm.
Glass spot plate with 8 or 12 wells.
H421-08: 110 x 70mm, 2 rows of 4 wells, well depth 2mm, well diameter 20mm, thickness of plate 5mm.
H421-12: 80 x 60mm, 3 rows of 4 wells, well depth 2mm, well diameter 16mm, thickness of plate 5mm.
|Type||Plate Dimensions (mm)||Wells Dimensions (mm)|
|6 wells||85 x 54 x 13||21 x 6|
|12 wells||115 x 90 x 14||21 x 6|
These economical white plastic spot dishes are suitable for most applications where glass or porcelain dishes are used. However, they are not recommended for strong solvents such as acetone or xylene. Made from white polystyrene, size 112 x 92mm with 12 wells, Ø 22mm, depth 6mm. Sold in package of 6.